How To Adjust Office Chair Height Without Lever

comfortable <a href=office chair and desk”/>

Getting comfortable at the office, whether you are in a traditional workplace or working from home, can be pretty difficult. There are already so many distractions, so the last thing you need is to keep wiggling around every few minutes.

In fact, apart from ruining your concentration, a chair with a broken lever stuck at the wrong height can limit your ability to assume the proper posture, causing wrist, knee, and back pain in the long run. The problem is that you don’t always have the budget to just go out and buy a brand-new office chair, or your boss keeps ignoring the issue.

Don’t worry – there are ways to raise office chair height even without the lever, so you can stay somewhat comfortable until it’s time to get a new chair, and there are plenty of great used options if your budget is tight.

Why Adjusting Office Chair Height is Essential

woman adjusting her posture in office

In general, to get into a comfortable sitting position at a computer, you want to keep your feet flat on the floor with the knees at about a 90-degree angle and a couple of inches of clearance between the thighs and the edge of the desk. That’s why you need to take the desk height into account when adjusting your office chair.

That should allow you to keep your back and neck fairly straight and the elbows flared out and at close to 90 degrees as well, making it easier for your wrist to sit flat on the desk to prevent strain.

It’s a neutral posture that keeps all the joints and vertebrae pain-free, allows for proper blood flow, and keeps your thighs from bumping into the desk every time you fidget slightly or readjust your position.

That’s why having an ergonomic, or at least comfortable, office chair set at the right height is so important for your productivity and long-term health.

Understanding Office Chair Design and Height Adjustment Mechanisms

The basic mechanism in any office chair is the pneumatic cylinder, usually filled with pressurized nitrogen gas, that is activated with a simple height adjustment lever. The lever is just a simple bent piece of metal with a flat plastic surface on one end that serves as a handle.

Moving it releases the cylinder, allowing it to move freely, and the gas pushes it up as it tries to match the atmospheric pressure around it, expanding in the process. Unless there is weight on the chair, the gas will push it to its full height, and unless it is locked in place by the metal bar, it will always push upwards until the chair reaches maximum height.

The most common problem you have with an office chair lever is that it no longer locks the gas cylinder in place, so it’s always at the highest setting until someone sits down and squashes it down to the lowest height. The other option is that it won’t unlock the cylinder from the previously set seat height, so it always just stays locked in one setting.

Luckily, you can use different tools and hacks to adjust the seating position manually without a height adjustment lever.

Alternative Methods to Adjust Office Chair Height

office chair in natural lighting

If your lever isn’t functioning properly and you can’t get the correct height and comfortable seating position you need, you can use these simple tips for a quick DIY solution.

Before you do, though, be sure to check whether there is any debris obstructing the lever and try to wiggle around a bit when you sit down and pull the lever to loosen the mechanism up in case it’s stuck. If that doesn’t do anything, move on to the following solutions.

Using a Screw Mechanism

Most office chairs will feature some type of manual adjustment option, usually a simple screw mechanism. To get the proper chair height, you need to turn the chair upside down and look for a prominent screw in the base. As you slowly unscrew it, the cylinder will start to move, and at this point, you can set the seat height manually and tighten it back down.

Modifying the Chair Base

A quick but temporary solution is to use a PVC pipe, cut lengthwise and attached to the cylinder to keep everything locked in at the appropriate chair height.

Metal or plastic table leg extenders are also a good option. Once you’ve made the right chair height adjustments and can sit comfortably, you can use duct tape to secure everything in place and make it just a tad bit sturdier.

These hacks will work fine for a while, but you won’t be able to make any further adjustments on the fly, which could be a problem if you share the chair with someone or if you’ve just had a big lunch and need a bit more between you and the desk.

Adjusting the Seat Cushion

The most low-tech solution, where you don’t have to mess around with the mechanism or use any extra tools to adjust it to the desired height, is to just find a nice thick seat cushion or a couple of regular ones stacked on top of each other to give you those few extra inches.

While it is a very comfortable option, you’ll want a cushion with adequate support to help you maintain proper posture – you don’t want your lower back to round too much or to be unbalanced and shifting around all the time.

When to Replace Your Office Chair

business woman in chair contemplating

These quick fixes are all fine, but how do you know it’s time to just get a new chair? It’s all about enhancing productivity, so if you are after optimal comfort without regularly adjusting and patching up temporary fixes, you’ll eventually need to move on.

Well, if the height adjustment mechanism or the pneumatic cylinder is completely broken and you can’t get into a comfortable position with any of our hacks, you should consider getting a new office chair.

Yes, new chairs can be expensive, especially ergonomic models that promote proper posture and give you the most comfortable position during extended periods of work, but you can also look at refurbished office chairs.

Look for lumbar support, the proper weight rating, a gas lift cylinder that works smoothly, and comfortable cushioning on the seat.

Conclusion

You can still make adjustments to an office chair without a working lever, but it will take you some time and elbow grease. With the tips we’ve outlined above, a few basic items and tools you can find in virtually any store, you can ensure good posture and get some more mileage out of your chair.

However, if you work for long hours, you will eventually want to adjust the height or find that your chair lacks adequate support. In that case, you’ll want to think about getting a new one or going with a used chair to save some money.

You can find more tips on adjusting office furniture to get that perfect seating position at OffiSavvy. We also offer a range of used office chairs from the biggest and most popular brands like Knoll, Herman Miller, Steel, and Haworth, as well as desks, so be sure to check them out.

Looking for Office Furniture in San Diego?

Visit the Offisavvy showroom at 7668 Miramar Rd., Suite B, San Diego, CA 92126 — we carry new and used office furniture including ergonomic chairs, standing desks, cubicles, and more. Call 858-727-5444 or request a quote online.

Shop Office Chairs in San Diego  Browse All Used Furniture →

About Author

Latest News

0
0
Your Cart
Your cart is emptyReturn to Shop